Skip to main content
Email :rxmarinechemical@gmail.com
Contact: 91 08069976670,
91 08069976671 , 91 08069976672

Alkali Cleaner RXSOL ORG - 6

 

 

Alkali Cleaner RXSOL ORG - 6
SKU
RXSOL-20-2059-027
Product Alias::
Supply Location::

RXMARINE CHEMICAL TAG::


Description::
Short Description
All purpose degreaser for cleaning of Oil and Sludge with emulsifiers. It is an excellent blend of powerful alkaline base and emulsifying inorganic products .Specially designed for engine room , machinery parts and cargo tank cleaning .

Application::
  • Prior to all kind of plating.
  •  Prior to Blackening and Phosphating.
  •  In a continuous Automatic strip, wire or coil cleaning purposes.

Oil and Sludge remover

RXSOL-20-2059-025 / 050   is  recommended for local cleaning & degreasing of engine rooms, bilges & tank  tops. It may be applied by brush, spray, immersion, soaking, or  any  other  conventional  means.RXSOL-20-2059-210 is used  neat. Allow a residence time of at least 20- 45 minutes where  possible, to ensure good penetration & emulsification. Finally wash the system with hot water & high pressure.The emulsion residue after cleaning must be allowed  to separate  in a holding tank for atleast 3-5 hours before passing through an oily water separator.

Tank Cleaning  Sludge/ Lube Oils / Slope-Black Oil
1 ) Fill the tank with 1-35 litres per ton wash water.Best results are obtained when water is heated to a   temperature  between  65°C & 80°C  then  stripped  constantly and transferred  to a holding  tank  for  separation.The time for this will vary depending on amount of RXSOL-20-2059-210  used & nature of oil being cleaned.Generally,12 hours should be sufficient before the water phase can be removed.
2) Direct Cleaning.Spray directly  RXSOL-20-2059-210 on tank surfaces to be cleaned, left  for at least 30  minutes.Finally wash with hydrogating (high pressure) machine. Hot water between 50°C & 80°C recommended.

  •  Prior to all kind of plating.
  •  Prior to Blackening and Phosphating.
  •  In a continuous Automatic strip, wire or coil cleaning purposes.

Technical Specifications::

 

Appearence           

Clear (Raw material depended colour of the effectively  will , however not be impaired .)

 

Density                   

1.48  - 1.50 @15°C

 

Total Alkalinity % by Mass 50% Minimum  

Flash Point           

Non Flammable

 

Foaming Non Foaming  

Solubility

100 % soluble in cold and hot water with any ratio.

 

Compatibility  

 

 

Metal                            

No known effect

 

Rubber                       

Do not use with natural rubber compounds

 

Shelf Life 18 month from Date of manufacturing

Dose::

Dose rate and results will vary depending on amount of contamination . For light contamination dilution with water up to 1:20 is recommended, where as medium contamination  dilute 1:10, And for heavy contamination neat RXSOL-20-2059-025 / 050 is suggested to use.

Dosage:- Dose rate and results will vary depending on  amount of contamination and deposit of oil grease, Soil etc . For light contamination dilution with water up to 1:20 is recommended, where as medium contamination  dilute 1:10, And for heavy contamination neat RXSOL-20-2059-025 / 050 is suggested to use.

OPERATING CONDITIONS

  FERROUS NON-FERROUS
Concentration  50-80 g/l 25-30 g/l
Temperature  65-80ºC 65-80ºC
Time 2-5 Mins.  2-5 Mins.

BATH MAKE UP

  • Fill the tank approximately 2/3 rd of the tank with warm water.
  • Add the required amount of RXSOL-20-2059-025 / 050 and stir till Homogenous homogenous.
  • Fill the tank to working level with water and heat to operating temperature.

MAINTENANCE

The concentration of the bath can be best determined by simple acid base titration using phenolphthalein as indicator.

Titrate 5ml of sample solution against 1N H2SO4. The concentration of the cleaner can be known by the formula given below : Calculation : Conc. = R x N x 15 Where, R = Burette reading N = Normality of H2SO4. 

Any grease that collects on the surface during operation should be removed in order to avoid resoiling of components during lifting out of the solution. The loss of water by evaporation has to be made up from time to time. If the solution acts slowly after some period of usage and some components are no longer sufficiently cleaned, the bath should be replaced with the new one.

EQUIPMENT

Plain steel tank is recommended. Heater made of steel or quartz can be used for heating purpose

CONTROL
The cleaner solution can easily and effectively be controlled by removing floating oil over the surface either manually or by means of circulating pump and an oil trap regularly. The concentration of the solution can be maintained by analysing the alkalinity of the solution by simple titration with standard acid using Phenolphthalein as an indicator.

Another Procedure of use for clean small spare Parts :- RXSOL-20-2059-025 / 050  is  recommended for  cleaning & degreasing of metal pipe, spare parts . It may be applied by brush, spray, immersion, soaking, or  any  other  conventional  metosd. RXSOL-20-2059-210 is used  neat. Allow a residence time of at least 20- 45 minutes where  possible, to ensure good penetration & emulsification. Finally wash the system with hot water & high pressure.The emulsion residue after cleaning must be allowed  to separate  in a holding tank for atleast 3-5 hours before passing through an oily water separator.

Tank Cleaning  Sludge/ Lube Oils / Slope-Black Oil : 
1 ) Fill the tank with 1-35 litres per ton wash water.Best results are obtained when water is heated to a   temperature  between  65°C & 80°C  then  stripped  constantly and transferred  to a holding  tank  for  separation.The time for this will vary depending on amount of RXSOL-20-2059-025 / 050  used & nature of oil being cleaned.Generally,12 hours should be sufficient before the water phase can be removed.
2) Direct Cleaning.Spray directly  RXSOL-20-2059-025 / 050 on tank surfaces to be cleaned, left  for at least 30  minutes.Finally wash with hydrogating (high pressure) machine. Hot water between 50°C & 80°C recommended.


Product remark::
Remarks

Alkali Cleaner manufacturer and supplier in Varanashi, Mumbai, Mughalsarai, Luckhnow, Kandla, Gandhidham, Kolkata, Chennai, Vizag - Visakhapatnam - INDIA.


Industrial Usages::

Useful Area::

Related Information::
Note

Characteristics:-

High penetration & emulsification   , Reduces down time.
Low toxicity, non -corrosive. Highly effective, economical solvent cleaner.
For cleaning of machinery parts, bulk heads, decks, bottom plates & any oil/grease dirty areas.
Used for cargo tank cleaning of mineral oils and petroleum based chemicals, Sludge etc .

CAUTION : RXSOL-20-2059-025 / 050 is alkaline in nature and contact of the skin or eyes should be avoided.

NOTE : The data set forth in this Bulletin is believed by RX Marine International to be true, accurate and complete but is not guaranteed. Our sole warranty is as stated in our standard Terms and Conditions of Sale. We cannot warrant out customers will achieve the same results from any bulletin because we do not have control over the condition of use; nor can we assume any responsibility for our products in a manner which infringes the patents of third parties.

 

Product Category

Copyright © 2021 Powered By RXMARINE - All Rights Reserved