1.Blue indicating silica gel contains cobalt chloride and is therefore extremely toxic for human use. Whereas, orange indicating silica gel does not contain cobalt chloride but contains methyl violet.
2.The cobalt chloride in blue silica gel allows it to change color from blue (when dry) to pink (when wet). Whereas, orange indicating silica gel changes from orange (when dry) to green (when wet).
RX MARINE INTERNATIONAL has ready stock of all three different color indicating silica gels in Mumbai, Gandhidham, Chennai, Vishakhapatnam, Kolkata, Fujairah and Oman.
Contact us for any queries:
Mail us at: mail@rxmarine.com
1.Nitrite Based COOL TREAT is to be added at a rate of 5 liters per 1,000 liters of the CW system capacity
2.MICROTREAT Micro biocide is to be added immediately after dosing with COOL TREAT at 2.5 liters per 1,000 liters of system of system capacity
#CoolingWaterTreatmentChemicals
#CoolWaterTreatment
RXSOL 2000 Antiscalant Corrosion Inhibitor Application: All types of Engine Jackets, Radiator and Engine coolant.
The stable oxide film that is formed by RXSOL 2000 prevents corrosion caused by electrolytic action between dissimilar metals used in the system . RXSOL 2000 has been field tested and found to have no detrimental effects on non metallic substances such as seals, glands, packing, hoses, gaskets etc., normally used in these’ systems.
Application-Dg*
Sets Internal combustion engines closed circuit cooling system compressor cooling system. Rxsol 2000-II incorporates superior corrosion inhibitors to prevent corrosion works by free of scale deposits.
Advatages benefit of Antiscalant Corrosion Inhibitor RXSOL 2000 for Engine : -
1. Prolong the life of equipment by keeping scale and corrosion free. Since RXSOL 2000 Ltr is alkaline and so will suppress acid corrosion, which would otherwise result in corrosion damage such as pitting. However, the alkalinity control is such that even if the product is accidentally overdosed, the pH of the water will remain within limits. The metals which would be affected by extremes of alkalinity or acidity are protected. protect cast iron diesel engine cooling systems.
2. Improves generating cooling efficiency by maintaining a clean heat transfer by protect against sludge and mineral scale formation.
3. Corrosion protection by using superior corrosion inhibitor.
4. Reduced maintenance and down time
5. Compatible with Coolants / Antifreeze solution / Glycol .
6. Friendly with Metals (Like steel, Copper, Aluminum, all alloys) & Non-metal (Rubber, Hoses, Gasket , and ‘O’rings.etc.)
7. Prevents over heating Effective against liner pitting and cavitation erosion.
NOTE :::
•Protects both ferrous and non-ferrous metals from oxygen & corrosion.
•Compatible with most coolants and anti frizzles.
•Non staining.
Antiscalant Corrosion Inhibitor RXSOL 2000 manufacturer and supplier in India, Oman, UAE, Sudan, Yemen, Kenya Nairobi
How to suppress Acid corrosion from Heat Transfer system like Radiator, DG Sets, Chiller Cooling water system, Closed cooling Water Circuit of diesel / petrol engine, Ice Water system etc.
RXSOL Roccor Nitrite Borax based Corrosion inhibitor Prolongs the life of equipment by keeping it scale and corrosion free. Since ROCCOR NB RXSOL-40-4001-025 is alkaline which effectively neutralize the ACIDIC corrosion affect.
The initial dosage of ROCCOR Nitrite Borax based corrosion inhibitor for an untreated system is 8 liters of product per 1000 liters of water. Such a dose will bring nitrite levels over 1200 ppm. Maximum nitrite level is considered to be 2400 ppm. Frequent tests should be carried out in order to maintain pH values within the limit (8.3-10.0), while levels of chloride should be maximum 50 ppm.
Corrosion Inhibitor for Cooling water System supplier in Mumbai, Kandla, Chennai, Visakhapatnam, Kolkata, Haldia, Paradip, Fujairah, Dubai, Ajman, Sharjah.
Mail us to get discounted price of Corrosion Inhibitor Roccor NB cooling water treatment chemicals. ::: mail@rxmarine.com
DOSES and Using procedure of Nitrite Borax Corrosion Inhibitor?
GENERAL RECOMMENDATION : ( The dosage chart may be used as a guide to adjust treatment to obtain the optimum level.)
Nitrite (as PPM NO2) 0 100-200 300-600 700-900 1100-1300
RXSOL-40-4001-025 / 1000L 8.0 7.3 7-8 5-7 1.5-3.5
NOTE ::: -- If nitrite level becomes 1440-2400 then doses should be ZERO.
The initial dosage for an untreated system is 8 liters of product per 1000 liters of water. Such a dose will bring nitrite levels over 1200 ppm. Maximum nitrite level is considered to be 2400 ppm. Frequent tests should be carried out in order to maintain pH values within the limit (8.3-10.0), while levels of chloride should be maximum 50 ppm.
Initial dosage for an untreated system is 9 litres of RXSOL-40-4001-025 / 1000 litres of untreated distilled water. This will bring the treatment up to the minimum level of 1000 ppm nitrite. For best result and prolonged engine life add RXSOL-40-4001-025 every 500 -6500 km. or 250 to 300 hours of running time or every 2 month interval. Specially designed for use in water systems of internal combustion equipment. pH should be maintained between 8.3 and 10 by the treatment.
RXSOL-40-4001-025 will react with sludge and in most cases, facilitate sludge gradual removal. On badly fouled systems with oil or scale, a prior degreasing by using DEGREASER HEAVY DUTY or descaling by using DEGREASER HEAVY DUTY, SCALE REMOVER LIQUID or SCALE REMOVER POWDER is highly recommended.
• Excellent corrosion inhibitor for cooling water
• Minimises metal oxide deposits
• Protects ferrous and non-ferrous metals
• Compatible with glycol-based antifreeze
• Reduces cleaning & maintenance costs
• Cost effective, easy to apply and use
How to Protect internal combustion engines, compressors, chiller system and DG sets from Corrosion from Nitrite Borax Corrosion Inhibitor Liquid?
Nitrite Borax Corrosion Inhibitor is a unique formulation with highly concentrated liquid cooling treatment compound, ferrous & Non ferrous corrosion inhibitors, antiscalants, dispersant and buffer solution of non carbonate.
Nitrite Borax Corrosion Inhibitor is specialized such a way which can be use in high or low temperature closed cooling water systems for the prevention of corrosion and scale formation in internal combustion engines, compressors, chiller system and DG sets. Also Usefull to Protects all metals including cast iron, mild steels and copper. Recommended ppm levels are easily controlled by standered RXSOL test kit Nitrite / Chloride.
The stable protective microfilm prevents corrosion caused by electrolytic action and the alkaline nature of this product prevents acid attack.
The stability of the added polymers are very useful for water treatment processes. Such polymers with low molecular weights cannot only inhibit calcium, magnesium, and silica scale in cooling towers and boilers, but also help corrosion control by dispersing iron oxide.
FIELDS ::: --- Suitable for use in closed water cooling systems, ice melting systems and transformer cooling systems. The product may be used in all kinds of diesel & petrol engines, compressor or heating cooling water circuits.
Where Nitrie Borax Corrosion Inhibitor can be used?
Prolongs the life of equipment by keeping it scale and corrosion free. Since RXSOL-40-4001-025 is alkaline, it will suppress acid corrosion, which would otherwise result in sever pittings. It improves cooling efficiency by maintaining clean heat transfer surfaces , from Radiators, DG - sets, Closed Cooling and chiller System.
FIELDS ::: --- Suitable for use in closed water cooling systems, ice melting systems and transformer cooling systems. The product may be used in all kinds of diesel & petrol engines, compressor or heating cooling water circuits.
( Used as a corrosion inhibitor for all ferrous and non-ferrous metals found in water systems )
Where Nitrite Borax Corrosion Inhibitor can be used?
Prolongs the life of equipment by keeping it scale and corrosion free. Since RXSOL-40-4001-025 is alkaline, it will suppress acid corrosion, which would otherwise result in sever pittings. It improves cooling efficiency by maintaining clean heat transfer surfaces , from Radiators, DG - sets, Closed Cooling and chiller System.
FIELDS ::: --- Suitable for use in closed water cooling systems, ice melting systems and transformer cooling systems. The product may be used in all kinds of diesel & petrol engines, compressor or heating cooling water circuits.
( Used as a corrosion inhibitor for all ferrous and non-ferrous metals found in water systems )
DOSES and Using procedure of Nitrite Borax Corrosion Inhibitor?
GENERAL RECOMMENDATION : ( The dosage chart may be used as a guide to adjust treatment to obtain the optimum level.)
Nitrite (as PPM NO2) 0 100-200 300-600 700-900 1100-1300
RXSOL-40-4001-025 / 1000L 8.0 7.3 7-8 5-7 1.5-3.5
NOTE ::: -- If nitrite level becomes 1440-2400 then doses should be ZERO.
The initial dosage for an untreated system is 8 liters of product per 1000 liters of water. Such a dose will bring nitrite levels over 1200 ppm. Maximum nitrite level is considered to be 2400 ppm. Frequent tests should be carried out in order to maintain pH values within the limit (8.3-10.0), while levels of chloride should be maximum 50 ppm.
Initial dosage for an untreated system is 9 litres of RXSOL-40-4001-025 / 1000 litres of untreated distilled water. This will bring the treatment up to the minimum level of 1000 ppm nitrite. For best result and prolonged engine life add RXSOL-40-4001-025 every 500 -6500 km. or 250 to 300 hours of running time or every 2 month interval. Specially designed for use in water systems of internal combustion equipment. pH should be maintained between 8.3 and 10 by the treatment.
RXSOL-40-4001-025 will react with sludge and in most cases, facilitate sludge gradual removal. On badly fouled systems with oil or scale, a prior degreasing by using DEGREASER HEAVY DUTY or descaling by using DEGREASER HEAVY DUTY, SCALE REMOVER LIQUID or SCALE REMOVER POWDER is highly recommended.
• Excellent corrosion inhibitor for cooling water
• Minimises metal oxide deposits
• Protects ferrous and non-ferrous metals
• Compatible with glycol-based antifreeze
• Reduces cleaning & maintenance costs
• Cost effective, easy to apply and use
How to Protect internal combustion engines, compressors, chiller system and DG sets from Corrosion from Nitrite Borax Corrosion Inhibitor Liquid?
Nitrite Borax Corrosion Inhibitor is a unique formulation with highly concentrated liquid cooling treatment compound, ferrous & Non ferrous corrosion inhibitors, antiscalants, dispersant and buffer solution of non carbonate.
Nitrite Borax Corrosion Inhibitor is specialized such a way which can be use in high or low temperature closed cooling water systems for the prevention of corrosion and scale formation in internal combustion engines, compressors, chiller system and DG sets. Also Usefull to Protects all metals including cast iron, mild steels and copper. Recommended ppm levels are easily controlled by standered RXSOL test kit Nitrite / Chloride.
The stable protective microfilm prevents corrosion caused by electrolytic action and the alkaline nature of this product prevents acid attack.
The stability of the added polymers are very useful for water treatment processes. Such polymers with low molecular weights cannot only inhibit calcium, magnesium, and silica scale in cooling towers and boilers, but also help corrosion control by dispersing iron oxide.
FIELDS ::: --- Suitable for use in closed water cooling systems, ice melting systems and transformer cooling systems. The product may be used in all kinds of diesel & petrol engines, compressor or heating cooling water circuits
Commissioning Cleanser is for cleaning of new boilers and cooling systems on board new buildings. It will remove scale, rust, oil and grease at the same time from the systems. The product is recirculated through the system, using an external circulation pump.
Use the dosage 5-10% solution depending on the grade of contamination.
Degreasing and descaling of boiler and cooling water systems
Drain system to be cleaned if necessary.
- Inspect as completely as possible to determine the extent of contamination and general condition of system.
- Fill with fresh water.
- Add a solution 5-10% strength of Commissioning Cleanser.
- Circulate through the system for 5 to 8 hours at the maximum temperature allowed by the system.
- Drain system complete and flush thoroughly the entire system and all compounds with fresh water until effluent is clear.
- Reinspect to determine results of the cleaning process.
- If unsatisfactory, repeat steps 3 through 7.
- Refill system with distillate or good quality fresh water and dose the required amount of cooling or boiler water treatment.
- Test system on a regular basis to insure chemical residuals are maintained with specific limits.
Dose value of Sea VOYAGE TANK CLEAN Plus can varies depends up on contamination and deposition of oil on the surface area. For tank cleaning " direct Injection Method " also one of the popular method. In this method, neat Sea VOYAGE TANK CLEAN can be injected directly from the drum through air-operated drum (barrel) pump. During this method this barrel pump can be connected to the pressure side of the automatic tank cleaning system line. Barrel Pump can be fixed at a predetermined rate as an injection rate of 0.1 0.2 liter Sea VOYAGE TANK CLEAN per 100 litres of tank wash water is sufficient. Cleaning time 2-6 hours. Finally wash and rinse the tank with water.
Spraying Method : If specific area of tank are heavily contaminated Use neat Sea VOYAGE TANK CLEAN overall soiled areas. Allow 10-20 minutes for reaction, then rinse with high pressure water hose., Scrubbing will assist the cleaning operation for stubborn deposits. Then above method can be started.
Use Handgloves, Goggles and safety mask before using in Tank. Keep container tightly closed and away from direct heat, fire and sunlight.
Recirculation Method for ship tank cleaning -
1) First of all heat the remaining oil in tanks .
2) By stripping constantly. flush the tank with sea water,
3) Close all suction and discharge valves .
4) Then make solution Voyage Tank Clean, RXSOL Emulsifier Solvent Degreaser with water with percentage ratio of 2-6% Voyage Tank Clean, RXSOL Emulsifier Solvent Degreaser ( 2 Ltr to 6 Ltrs in 100 Ltr Water ) concentration value can be increase as per cleaning demand and contamination and condition of tank. Circulate cleaning solution via the automatic tank washing system pump and heater to the tank to be cleaned, wherefrom the solution is returned to the chemical solution tank via the stripping line. The same solution can be repeated for 2 - 3 tanks, then new cleaning solution required if same solution repeated for more then 2-3 tanks. Finally after recirculation the tanks should be rinsed thoroughly with sea water or fresh water depending on availability and requirements.
Rock and Roll Method at sea Tank cleaning for double bottom tank:
Recommended time to clean and gas-free under normal circumstances would be 3-6 days ,for cleaning of double bottom tanks at sea.
1) First of all heat the remaining oil in tanks .
2) By stripping constantly. flush the tank with sea water,
3) Close all suction and discharge valves .
4)1st Dose Fill the tanks by ½ to 1 litre sea voyage Tank clean plus per tone of water through pipe or manhole , for 75-80% of capacity of tank to be cleaned.
5) Then fill tank to 25% capacity with sea water, raise the temperature up to 60°C maximum, and maintain this temperature for 24 hours.
6) Top up tank to 75-80% capacity with sea water, continue to heat for 48 to 72 hours.
7) Discharge and strip tank. Fill to 50-60% capacity with sea water and allow 2 hours rinsing time.
8) Discharge tank and strip, flushing tank with sea water for 2 hours,stripping continuously. When completed, inspect tank to ascertain if second cleaning is required. If so:
9) For completion add second dose of Sea Voyage Tankclean, fill tank with sea water 75-80% capacity and raise the temperature to 60°C maximum. Maintain this for 48 to 72 hours. And recirculate the solution .
10) Discharge and strip tank, flush with sea water, stripping continuously for 2 hours.
11) To gas-free, fill tank with sea water to overflow through vents and sounding pipes, discharge and strip completely.
One of largest Tank Cleaning Sea Marine Cleaning Chemical Supplier in Mumbai, Kandla, Sikka, Jamnagar, Kolkata, Ennore, Fujairah, Dubai, Abudhabi, Ajman, Sharjah, Muscat, Oman, Canada BC
Email : mail@rxmarine.com