Where Nitrite Borax Corrosion Inhibitor can be used?
Prolongs the life of equipment by keeping it scale and corrosion free. Since RXSOL-40-4001-025 is alkaline, it will suppress acid corrosion, which would otherwise result in sever pittings. It improves cooling efficiency by maintaining clean heat transfer surfaces , from Radiators, DG - sets, Closed Cooling and chiller System.
FIELDS ::: --- Suitable for use in closed water cooling systems, ice melting systems and transformer cooling systems. The product may be used in all kinds of diesel & petrol engines, compressor or heating cooling water circuits.
( Used as a corrosion inhibitor for all ferrous and non-ferrous metals found in water systems )
DOSES and Using procedure of Nitrite Borax Corrosion Inhibitor?
GENERAL RECOMMENDATION : ( The dosage chart may be used as a guide to adjust treatment to obtain the optimum level.)
Nitrite (as PPM NO2) 0 100-200 300-600 700-900 1100-1300
RXSOL-40-4001-025 / 1000L 8.0 7.3 7-8 5-7 1.5-3.5
NOTE ::: -- If nitrite level becomes 1440-2400 then doses should be ZERO.
The initial dosage for an untreated system is 8 liters of product per 1000 liters of water. Such a dose will bring nitrite levels over 1200 ppm. Maximum nitrite level is considered to be 2400 ppm. Frequent tests should be carried out in order to maintain pH values within the limit (8.3-10.0), while levels of chloride should be maximum 50 ppm.
Initial dosage for an untreated system is 9 litres of RXSOL-40-4001-025 / 1000 litres of untreated distilled water. This will bring the treatment up to the minimum level of 1000 ppm nitrite. For best result and prolonged engine life add RXSOL-40-4001-025 every 500 -6500 km. or 250 to 300 hours of running time or every 2 month interval. Specially designed for use in water systems of internal combustion equipment. pH should be maintained between 8.3 and 10 by the treatment.
RXSOL-40-4001-025 will react with sludge and in most cases, facilitate sludge gradual removal. On badly fouled systems with oil or scale, a prior degreasing by using DEGREASER HEAVY DUTY or descaling by using DEGREASER HEAVY DUTY, SCALE REMOVER LIQUID or SCALE REMOVER POWDER is highly recommended.
• Excellent corrosion inhibitor for cooling water
• Minimises metal oxide deposits
• Protects ferrous and non-ferrous metals
• Compatible with glycol-based antifreeze
• Reduces cleaning & maintenance costs
• Cost effective, easy to apply and use
How to Protect internal combustion engines, compressors, chiller system and DG sets from Corrosion from Nitrite Borax Corrosion Inhibitor Liquid?
Nitrite Borax Corrosion Inhibitor is a unique formulation with highly concentrated liquid cooling treatment compound, ferrous & Non ferrous corrosion inhibitors, antiscalants, dispersant and buffer solution of non carbonate.
Nitrite Borax Corrosion Inhibitor is specialized such a way which can be use in high or low temperature closed cooling water systems for the prevention of corrosion and scale formation in internal combustion engines, compressors, chiller system and DG sets. Also Usefull to Protects all metals including cast iron, mild steels and copper. Recommended ppm levels are easily controlled by standered RXSOL test kit Nitrite / Chloride.
The stable protective microfilm prevents corrosion caused by electrolytic action and the alkaline nature of this product prevents acid attack.
The stability of the added polymers are very useful for water treatment processes. Such polymers with low molecular weights cannot only inhibit calcium, magnesium, and silica scale in cooling towers and boilers, but also help corrosion control by dispersing iron oxide.
FIELDS ::: --- Suitable for use in closed water cooling systems, ice melting systems and transformer cooling systems. The product may be used in all kinds of diesel & petrol engines, compressor or heating cooling water circuits
Commissioning Cleanser is for cleaning of new boilers and cooling systems on board new buildings. It will remove scale, rust, oil and grease at the same time from the systems. The product is recirculated through the system, using an external circulation pump.
Use the dosage 5-10% solution depending on the grade of contamination.
Degreasing and descaling of boiler and cooling water systems
Drain system to be cleaned if necessary.
- Inspect as completely as possible to determine the extent of contamination and general condition of system.
- Fill with fresh water.
- Add a solution 5-10% strength of Commissioning Cleanser.
- Circulate through the system for 5 to 8 hours at the maximum temperature allowed by the system.
- Drain system complete and flush thoroughly the entire system and all compounds with fresh water until effluent is clear.
- Reinspect to determine results of the cleaning process.
- If unsatisfactory, repeat steps 3 through 7.
- Refill system with distillate or good quality fresh water and dose the required amount of cooling or boiler water treatment.
- Test system on a regular basis to insure chemical residuals are maintained with specific limits.
Dose value of Sea VOYAGE TANK CLEAN Plus can varies depends up on contamination and deposition of oil on the surface area. For tank cleaning " direct Injection Method " also one of the popular method. In this method, neat Sea VOYAGE TANK CLEAN can be injected directly from the drum through air-operated drum (barrel) pump. During this method this barrel pump can be connected to the pressure side of the automatic tank cleaning system line. Barrel Pump can be fixed at a predetermined rate as an injection rate of 0.1 0.2 liter Sea VOYAGE TANK CLEAN per 100 litres of tank wash water is sufficient. Cleaning time 2-6 hours. Finally wash and rinse the tank with water.
Spraying Method : If specific area of tank are heavily contaminated Use neat Sea VOYAGE TANK CLEAN overall soiled areas. Allow 10-20 minutes for reaction, then rinse with high pressure water hose., Scrubbing will assist the cleaning operation for stubborn deposits. Then above method can be started.
Use Handgloves, Goggles and safety mask before using in Tank. Keep container tightly closed and away from direct heat, fire and sunlight.
Recirculation Method for ship tank cleaning -
1) First of all heat the remaining oil in tanks .
2) By stripping constantly. flush the tank with sea water,
3) Close all suction and discharge valves .
4) Then make solution Voyage Tank Clean, RXSOL Emulsifier Solvent Degreaser with water with percentage ratio of 2-6% Voyage Tank Clean, RXSOL Emulsifier Solvent Degreaser ( 2 Ltr to 6 Ltrs in 100 Ltr Water ) concentration value can be increase as per cleaning demand and contamination and condition of tank. Circulate cleaning solution via the automatic tank washing system pump and heater to the tank to be cleaned, wherefrom the solution is returned to the chemical solution tank via the stripping line. The same solution can be repeated for 2 - 3 tanks, then new cleaning solution required if same solution repeated for more then 2-3 tanks. Finally after recirculation the tanks should be rinsed thoroughly with sea water or fresh water depending on availability and requirements.
Rock and Roll Method at sea Tank cleaning for double bottom tank:
Recommended time to clean and gas-free under normal circumstances would be 3-6 days ,for cleaning of double bottom tanks at sea.
1) First of all heat the remaining oil in tanks .
2) By stripping constantly. flush the tank with sea water,
3) Close all suction and discharge valves .
4)1st Dose Fill the tanks by ½ to 1 litre sea voyage Tank clean plus per tone of water through pipe or manhole , for 75-80% of capacity of tank to be cleaned.
5) Then fill tank to 25% capacity with sea water, raise the temperature up to 60°C maximum, and maintain this temperature for 24 hours.
6) Top up tank to 75-80% capacity with sea water, continue to heat for 48 to 72 hours.
7) Discharge and strip tank. Fill to 50-60% capacity with sea water and allow 2 hours rinsing time.
8) Discharge tank and strip, flushing tank with sea water for 2 hours,stripping continuously. When completed, inspect tank to ascertain if second cleaning is required. If so:
9) For completion add second dose of Sea Voyage Tankclean, fill tank with sea water 75-80% capacity and raise the temperature to 60°C maximum. Maintain this for 48 to 72 hours. And recirculate the solution .
10) Discharge and strip tank, flush with sea water, stripping continuously for 2 hours.
11) To gas-free, fill tank with sea water to overflow through vents and sounding pipes, discharge and strip completely.
One of largest Tank Cleaning Sea Marine Cleaning Chemical Supplier in Mumbai, Kandla, Sikka, Jamnagar, Kolkata, Ennore, Fujairah, Dubai, Abudhabi, Ajman, Sharjah, Muscat, Oman, Canada BC
Email : mail@rxmarine.com
Dear Sir,
Pl. suggest product Tank Cleaner to clean Cracker Fuel Oil which is not water soluble so Hydrocarbon Remover may also be required to complete the cleaning process. This cargo is not considered a good prior cargo for loading other high grade chemicals."
Thanks and Best Regards,
Vinod Nair
Ans :
Dear Sir,
GD DAY.
New ORG tank cleaner is highly effective on BLACK cargo - FUEL OIL. Its cleaning principle is based on emulsifier basis, which is effectively makes OIL deposited particle into water miscible. Its long chain compound penetrates into deposited mass and increases affinity towards water. Pl. review this link http://rxmarine.com/new-org , After using this product if cargo requirement is Hydrocarbon Free then CLEANING process can be repeated by using this prodcut http://rxmarine.com/ballast-tank-cleaner
One more advanced formulation products for same utility is available through this link ...http://rxmarine.com/tank-cleaner-hd
THanking you
WBRGDS
Rakshit
Sea Voyage Tank clean is one of popular heavy crude oil cleaning tank cleaner. Its strong emulsifying cleaning product penetrates in the heavy deposit of crude oil and makes water soluble, which makes cleaning easy through water pressure. Sea voyage oil cleaning degreasing formula also helps to clean almost all kinds of petroleum, lube oil, base oil products. Sea clean also contains penetrating solvent to make heavy deposits soft and presence of emulsifier in sea Voyage Tank clean helps to get solid mass easily disperse along with water.
We are one of the largest exporters of sea Voyage Tank clean from INDIA to Middle East / UAE, since 1995.
We have a stock point of sea Voyage Tank clean in Mumbai, Kandla, Surat, Chennai - Ennore, Visakhapatnam - Gangavaram, Kolkata - Haldia - Paradip, Goa, Fujairah - Sharjah - Mussafah Abudhabi, Dubai.
Standard packing of sea clean is 25, 50, 210 Ltrs DRUM.
Feel Free to ask for factory sale price of sea voyage tanks clean through email.
Seaclean@tankcleaner
NEW ORG is more powerful then SEA Voyage Tank CLEAN
Email : mail@rxmarine.com / rxmarine@gmail.com
Coldwash is specified marine degreasing and Cleaning Chemicals. Cold wash Cleaning application in Maintenance sector is most popular due to its non hazardous emulsifying agents. Cold wash effectively cleans greasy soiled mass from surface as well as machinery parts.
We are one of popular supplier of cold wash in INDIA - Mumbai, Kandla - Gandhidham, Chennia - Ennore, Visakhapatnam - Gangavaram, Kolkata - Haldia - Paradip. And in Middle East - Dubai - Fujairah - Sharjah.
We have new advanced formulation of COLD WASH chemicals, Which is more effective and powerful. New Generation Product - NEW ORG ( http://www.rxmarine.com/new-org )
India - mail@rxmarine.com
Middle East : dubichem@rxmarine.com
How to clean Pet Coke STAIN -
Coal and petcoke leaves stain, its removal is important task during hold cleaning operation. Our expert has 2 suggestion for removal of such stain from the surface.
1st one to use RX Tuff heavy-duty alkaline cleaner, which can apply as an emulsion, need time to take effect and are rinsed away with seawater. More than one application will be needed to remove stubborn stains.
2nd one solution is much more effective than 1st one step. Here our expert suggests using New ORG on the spotted area where the residue is tightly deposited on the surface. " New ORG -RXSOL-20-2020-025 " this product is specialized to react with oily residue where any alkaline cleaner fails to emulsify. Uses of New ORG chemicals for stain removal/cleaning principally dissolve and emulsify OIL RESIDUE stain completely which is resulting stain-free surface, Then without flushing with water follow 1st step.
Note 1 : Only 50 Ltr New ORG required to cover entire ship hold SPOT STAIN area. And it will not cost more than 100 US$, but its uses can save a full daytime. As pet coke contains oily residue. Only uses of alkaline cleaner doesn't emulsify oil properly.
Note 2 : New Org 50 Ltr is absolutely free alongwith order of RX Tuff, Aquatuff, Pet coke remover, If your order Qty is more then 1500 Ltr.
Muriatic Acid plays a very important role in cement cargo hold cleaning.
Step 1
Spray muriatic acid on entire cement covered area.including sidewalk or driveway. Do not let the liquid content evaporate fully from the surface. Wait for a day with no wind so you do not run the risk of acid spatters. Follow the precaution instructions and guidance on how to mix it with water. In general, you must use a plastic bucket.
Step 2
Test the acid on an inconspicuous portion of the concrete to make sure it won't damage the surface.
Step 3
Dip the masonry brush into the bucket. Scrub it into the concrete. If the stains don't lift right away, dip the brush back into the bucket and apply some of the acid solutions onto the concrete. Let it sit on the stains for no more than five minutes. Then scrub the concrete again.
Step 4
Rinse the concrete thoroughly with cool water.
Precaution Ensure Your Safety :
Step 1
Wear a respirator, eye mask, face mask and strong rubber gloves. Put on old clothing that fully covers your arms and legs. Wear socks and old shoes or boots; never go barefoot while working with muriatic acid.
Step 2
Keep a pressure washer right next to your work area in case of accidental spills. You might substitute a hose for the pressure washer, but only if it has strong water pressure. You'll also need the pressure to dilute and wash away the acid when you're finished.
Step 3
Protect other parts near your work area since muriatic acid can damage, then cover these areas with a tarp.
Step 4
Keep flames, heat and sparks far away from the acid. Muriatic acid is not flammable, but it can form a flammable hydrogen gas if it comes into contact with metal.