Product Dose

Dose rate and results will vary depending on amount of contamination . For light contamination dilution with water up to 1:20 is recommended, where as medium contamination  dilute 1:10, And for heavy contamination neat RXSOL-20-2059-025 / 050 is suggested to use.

Dosage:- Dose rate and results will vary depending on  amount of contamination and deposit of oil grease, Soil etc . For light contamination dilution with water up to 1:20 is recommended, where as medium contamination  dilute 1:10, And for heavy contamination neat RXSOL-20-2059-025 / 050 is suggested to use.


Concentration  50-80 g/l 25-30 g/l
Temperature  65-80ºC 65-80ºC
Time 2-5 Mins.  2-5 Mins.


  • Fill the tank approximately 2/3 rd of the tank with warm water.
  • Add the required amount of RXSOL-20-2059-025 / 050 and stir till Homogenous homogenous.
  • Fill the tank to working level with water and heat to operating temperature.


The concentration of the bath can be best determined by simple acid base titration using phenolphthalein as indicator.

Titrate 5ml of sample solution against 1N H2SO4. The concentration of the cleaner can be known by the formula given below : Calculation : Conc. = R x N x 15 Where, R = Burette reading N = Normality of H2SO4. 

Any grease that collects on the surface during operation should be removed in order to avoid resoiling of components during lifting out of the solution. The loss of water by evaporation has to be made up from time to time. If the solution acts slowly after some period of usage and some components are no longer sufficiently cleaned, the bath should be replaced with the new one.


Plain steel tank is recommended. Heater made of steel or quartz can be used for heating purpose

The cleaner solution can easily and effectively be controlled by removing floating oil over the surface either manually or by means of circulating pump and an oil trap regularly. The concentration of the solution can be maintained by analysing the alkalinity of the solution by simple titration with standard acid using Phenolphthalein as an indicator.

Another Procedure of use for clean small spare Parts :- RXSOL-20-2059-025 / 050  is  recommended for  cleaning & degreasing of metal pipe, spare parts . It may be applied by brush, spray, immersion, soaking, or  any  other  conventional  metosd. RXSOL-20-2059-210 is used  neat. Allow a residence time of at least 20- 45 minutes where  possible, to ensure good penetration & emulsification. Finally wash the system with hot water & high pressure.The emulsion residue after cleaning must be allowed  to separate  in a holding tank for atleast 3-5 hours before passing through an oily water separator.

Tank Cleaning  Sludge/ Lube Oils / Slope-Black Oil : 
1 ) Fill the tank with 1-35 litres per ton wash water.Best results are obtained when water is heated to a   temperature  between  65°C & 80°C  then  stripped  constantly and transferred  to a holding  tank  for  separation.The time for this will vary depending on amount of RXSOL-20-2059-025 / 050  used & nature of oil being cleaned.Generally,12 hours should be sufficient before the water phase can be removed.
2) Direct Cleaning.Spray directly  RXSOL-20-2059-025 / 050 on tank surfaces to be cleaned, left  for at least 30  minutes.Finally wash with hydrogating (high pressure) machine. Hot water between 50°C & 80°C recommended.

RX MARINE INTERNATIONAL is most popular chemicals source in INDIA, Keeping ready stock at 5 LOCATION which includes Mumba, Kandla - Gandhidham, Vizag - Visakhapatnam, Ennore - Chennai, Kolkata more then 3000 types of chemicals. Please click here to get PRODUCT Categories details


Mail Us for any PRODUCT related information and purchase inquiry : ( This mail is for customer / Buyer only ) And if you wants to add your hand as a supplier, And if you have volume manufacturing capacity of chemicals, pl. drop your mail at ( This mail is for supplier only )